1. Extrinsic semiconductors have more current conducting capacity than intrinsic semiconductors

2. Any transistor designed must operate in the ________ region of the characteristic curve

3. A transformer only increases the voltage with corresponding increase in current

4. The process of setting up a current to operate a transistor at a desired point on its characteristic curve is known as __________

5. Which of the following is/are true

I. Reverse biasing prevents the flow of charge carriers across the junction.

II. Forward biasing is created when the positive terminal is connected to the n-type part of the PN junction.

III. In practice, when we apply reverse biasing to a PN junction, all the charge carriers stops to flow.

6. Which of these will result in forward biasing

I. when certain dc voltage is applied to the junction in such a direction that it cancels the potential barrier thus permitting the flow of current

II. Connecting the negative terminal of the battery to the p-type and positive terminal to the n-type

III. Connecting the positive terminal of the battery to the p-type and negative terminal to the n-type

IV. when certain dc voltage is applied to the junction in such a direction that the potential barrier is increased

7. when the sensitivity of a meter is high, it means the meter has .............

8. The voltage signal at the collector is out of phase with the signal at the base by:

9. What is known as eddy current loss in a transformer?

10. ...................... are responsible for the conduction  in a conductor

11. A hole can also be described as a _________

12. A mesh is any closed path in a circuit which does not enclose any other closed path inside it

13. If a circuit has the following parameters Vcc =20V, Rs +Rm = 9.3KΩ, Vbe = 0.7, Im =1mA, and Β = 100. Calculate the meter current when E =10V and the voltmeter input r with or without the transistor.

14. In a semiconductor, as temperature increases, conductivity ..................

15. In electronics, _____ refers to the use of DC voltage to establish certain operating conditions for an electronic device.

16. When a small amount of trivalent impurity is added to a pure semi conductor, the semi conductor becomes

17. In checking for continuity of circuit which on these is used

18. The emf that gets induced in the secondary winding according to Faraday's law of electromagnetic induction is called?

19. A perfect amplifier has all of the following properties except:

20. The core in a transformer provides ?

21. Copper loss is usually larger than other losses

22. Which of the statements about PN junction is true

I. A PN junction presents a high resistance if forward biased.

II. A PN junction presents a high resistance if reversed biased.

III A PN junction presents a low resistance if forward biased.

IV. A PN junction presents a low resistance if reversed biased.

23. A resistor is regarded as a circuit element which puts energy into a circuit

24. A capacitor C and an Inductor L store................. and .................... respectively

25. Coils are ............... separated, but ................ linked together

26. p-type and n-type semiconductor join together to form a ................. known as ................

27. On the basis of their use, transformers are classified as

28. Which of this must be connected to multimeter to be able to measure AC voltages?

29. In a multimeter, when the variable resistance and the fixed resistance are connected in series with the battery and galvanometer, the multimeter functions as

30. The transistor is a three-terminal device that we can use to form a _____________ circuit

31. A multiplier measures .................., ....................... and .....................

32. The potential barrier of a P-N junction depends on which of the following except

33. Which of the following is true about the effect of temperature on semiconductors

I. At absolute zero, there are no free electrons.

II. Above absolute zero, bonds break and electrons move under the influence of the applied electric field.

III. The semiconductor has its highest conductivity at absolute zero

IV. The semiconductor behaves as a perfect insulator at absolute zero

34. The majority carriers in an n-type semiconductor is ?

35. Inductors are very common in high-frequency circuit

36. The resistivity of a semiconductor is .......... that of an insulator, and ............that of conductors

37. A galvanometer measures and detects extremely small currents both in ..................... and ...........................

38. The principle behind the working of a transformer is _________

39. Select the correct options only

I. Pentavalent impurities provide large number of free electrons to the semiconductor.

II. Trivalent impurities provide large number of free electrons to the semiconductor.

III. Trivalent impurities provide large number of holes to the semiconductor.

IV. Pentavalent impurities provide large number of holes to the semiconductor.

40. Which of this is true

41. Calculate Ia, Ib and Ic

42.

How many branches, nodes, loop and mesh do we have here?

43. No electrons can stay in the forbidden gap because

44. Which of the following is/are correct?

I. Bipolar junction transistors control the current by varying the number of charge carriers

II. Voltage between 2 terminals are indicated by repeated letters

III. The emitter is lightly doped to reduce junction capacitance

IV. The emitter-base junction is forward biased

45. The e–h+ pair can also be called ____

46. A material that releases an electron from the valence band into the conduction band when a photon of light is incident on it is a ___________

47. A capacitor stores charge and hence, electric energy

48. The loss due to ohmic resistance of the transformer windings

49. ________ converts alternating currents into direct currents

50. The separation between conduction band and valence band on the energy level diagram is called ________

51. A emitter-follower circuit has Vcc =12V, Rm = 1KΩ and a 2mA meter. If the amplification factor of the resistor is 80 and Vbe = 0.7. Calculate the suitable r for Rs to give fsd when E= 5V.

52. Calculate Rth, Vth, and I5

53. Which of the following is correct

I. Small changes in V(BE) will produce large current changes in I(C) & I(E)

II. Small changes in V(CE) have little effect on I(B)

III. Small changes in V(CE) will produce large current changes in I(C) & I(E)

I, II, III & IVIV. Small changes in V(BE) will produce large current changes in I(B)

54. In pure inductors, current ......... the voltage by ......

55. What is the number of branches, nodes, loops, and meshes?

56. The transistor is a current __________ device.

57. A component that allows the flow of current in only one direction is called ..........

58. A Thevenin's equivalent circuit contains an equivalent source Vth in parallel with an equivalent resistor Rth

59. A p-n junction is also known as

60. Which of the following transformers has a high rating?

61. In a transformer, most flux which get linked to the secondary winding is called?

62. A 6600/550V, 25KVA transformer has iron losses of 350W and its 1º and 2° winding resistances are 14.5 and 0.1Ω respectively. Determine the full load efficiency at a power factor of unity.

63. A variable resistor in an electric circuit is for ...............

64. In an RL circuit voltage across the resistor increases exponentially

65. Which of the following is true about transformers?

I. Open circuit test are done with a load on the transformer.

II. Copper loss is due to the ohmic resistance of the transformer windings.

III. Open circuit test is done to determine the 'no load loss' of the transformer.

IV. A transformer is electrically linked.

66. Circuit elements connected in series have common ................. passing through each element

67. Depletion layer serves as barrier to the movement of free electrons.

68. A capacitor and an Inductor in an AC circuit is referred to as

69. A node is a collection point for two or more banches

70. What type of bonds exist in semiconductors

71. Calculate the equivalent resistance

72. The loss due to the reversal of magnetization in the transformer core is known as

73. What are the examples of passive elements?

74. Voltmeter draws ........................ current

75. Why is a laminated steel core used in a transformer instead of a solid core?

76. The collector current is determined by the _________

77. An ammeter also detects the direction of the flow of current

78. Consider the following statements and choose only correct answers

I. The resistivity of a semiconductor is less than that of an insulator and more than a conductor

II. As temperature increases, the conductivity of semiconductors decreases

III. We can consider a semiconductor as a resistance material

IV. Semiconductors have a negative temperature coefficient of resistance

79. Inductors smoothen sharp sudden changes in ..........

80. AC Current and Voltage may vary with time. True or False?

81. The most versatile circuit configuration for transistors is the

82. Calculate the current flowing in the circuit

83. In a RC circuit, voltage across the resistor ................... exponentially with time

84. A meter is protected in the case of accidental workload by connecting ............... in .............. with a voltmeter

85. The Norton's equivalent circuit contains a Norton equivalent source "I(N)" in parallel with an equivalent resistor R(N)

86. Which of the following statements is/are true? I. A multimeter can be used as an ammeter when low resistance is connected in parallel with the galvanometer II. A low sensitive meter will measure Voltage perfectly III. A multimeter cannot be used to determine circuit continuity IV. A multimeter can be used as an voltmeter when high resistance is connected in series with the galvanometer

87. An Inductor tend to smooth sudden change in .................

88. The arrangement of atoms in a repetitive manner is known as

89. Loading effect of a meter happens because...............

90. A inductor stores energy in its _________

91. A semiconductor in an extremely pure form is known as .............

92. To convert a multiplier to an ammeter, a .......... resistance is connected in .................. with a galvanometer

93. Circuit elements are connected in parallel when a common ................ is applied to each elements

94. A transformer consists of two inductive coils namely;

95. A laminated steel core that has high silicon content provides