1. In an RL circuit voltage across the resistor increases exponentially

2. A perfect amplifier has all of the following properties except:

3. Which of the following statements is/are true? I. A multimeter can be used as an ammeter when low resistance is connected in parallel with the galvanometer II. A low sensitive meter will measure Voltage perfectly III. A multimeter cannot be used to determine circuit continuity IV. A multimeter can be used as an voltmeter when high resistance is connected in series with the galvanometer

4. Which of this must be connected to multimeter to be able to measure AC voltages?

5. To convert a multiplier to an ammeter, a .......... resistance is connected in .................. with a galvanometer

6. ...................... are responsible for the conduction  in a conductor

7. A component that allows the flow of current in only one direction is called ..........

8. Which of the following transformers has a high rating?

9. Copper loss is usually larger than other losses

10. Coils are ............... separated, but ................ linked together

11. A capacitor and an Inductor in an AC circuit is referred to as

12. The transistor is a current __________ device.

13. Inductors smoothen sharp sudden changes in ..........

14. Which of these will result in forward biasing

I. when certain dc voltage is applied to the junction in such a direction that it cancels the potential barrier thus permitting the flow of current

II. Connecting the negative terminal of the battery to the p-type and positive terminal to the n-type

III. Connecting the positive terminal of the battery to the p-type and negative terminal to the n-type

IV. when certain dc voltage is applied to the junction in such a direction that the potential barrier is increased

15. The voltage signal at the collector is out of phase with the signal at the base by:

16. A multiplier measures .................., ....................... and .....................

17. The collector current is determined by the _________

18. Any transistor designed must operate in the ________ region of the characteristic curve

19. Loading effect of a meter happens because...............

20. A transformer only increases the voltage with corresponding increase in current

21. The loss due to ohmic resistance of the transformer windings

22. A emitter-follower circuit has Vcc =12V, Rm = 1KΩ and a 2mA meter. If the amplification factor of the resistor is 80 and Vbe = 0.7. Calculate the suitable r for Rs to give fsd when E= 5V.

23. A capacitor C and an Inductor L store................. and .................... respectively

24. A Thevenin's equivalent circuit contains an equivalent source Vth in parallel with an equivalent resistor Rth

25. The e–h+ pair can also be called ____

26. What type of bonds exist in semiconductors

27. A capacitor stores charge and hence, electric energy

28. Which of the statements about PN junction is true

I. A PN junction presents a high resistance if forward biased.

II. A PN junction presents a high resistance if reversed biased.

III A PN junction presents a low resistance if forward biased.

IV. A PN junction presents a low resistance if reversed biased.

29. Which of the following is correct

I. Small changes in V(BE) will produce large current changes in I(C) & I(E)

II. Small changes in V(CE) have little effect on I(B)

III. Small changes in V(CE) will produce large current changes in I(C) & I(E)

I, II, III & IVIV. Small changes in V(BE) will produce large current changes in I(B)

30. The principle behind the working of a transformer is _________

31. The majority carriers in an n-type semiconductor is ?

32. When a small amount of trivalent impurity is added to a pure semi conductor, the semi conductor becomes

33. In pure inductors, current ......... the voltage by ......

34. In a RC circuit, voltage across the resistor ................... exponentially with time

35. Which of the following is true about the effect of temperature on semiconductors

I. At absolute zero, there are no free electrons.

II. Above absolute zero, bonds break and electrons move under the influence of the applied electric field.

III. The semiconductor has its highest conductivity at absolute zero

IV. The semiconductor behaves as a perfect insulator at absolute zero

36. If a circuit has the following parameters Vcc =20V, Rs +Rm = 9.3KΩ, Vbe = 0.7, Im =1mA, and Β = 100. Calculate the meter current when E =10V and the voltmeter input r with or without the transistor.

37. Calculate the current flowing in the circuit

38. A transformer consists of two inductive coils namely;

39. A inductor stores energy in its _________

40. AC Current and Voltage may vary with time. True or False?

41. Which of the following is/are correct?

I. Bipolar junction transistors control the current by varying the number of charge carriers

II. Voltage between 2 terminals are indicated by repeated letters

III. The emitter is lightly doped to reduce junction capacitance

IV. The emitter-base junction is forward biased

42. A node is a collection point for two or more banches

43. An Inductor tend to smooth sudden change in .................

44. What is known as eddy current loss in a transformer?

45. The loss due to the reversal of magnetization in the transformer core is known as

46. Consider the following statements and choose only correct answers

I. The resistivity of a semiconductor is less than that of an insulator and more than a conductor

II. As temperature increases, the conductivity of semiconductors decreases

III. We can consider a semiconductor as a resistance material

IV. Semiconductors have a negative temperature coefficient of resistance

47. The potential barrier of a P-N junction depends on which of the following except

48. In a transformer, most flux which get linked to the secondary winding is called?

49. ________ converts alternating currents into direct currents

50. The emf that gets induced in the secondary winding according to Faraday's law of electromagnetic induction is called?

51. A material that releases an electron from the valence band into the conduction band when a photon of light is incident on it is a ___________

52. In a semiconductor, as temperature increases, conductivity ..................

53. On the basis of their use, transformers are classified as

54. Voltmeter draws ........................ current

55. What is the number of branches, nodes, loops, and meshes?

56. A galvanometer measures and detects extremely small currents both in ..................... and ...........................

57. A hole can also be described as a _________

58. A semiconductor in an extremely pure form is known as .............

59. The Norton's equivalent circuit contains a Norton equivalent source "I(N)" in parallel with an equivalent resistor R(N)

60. In a multimeter, when the variable resistance and the fixed resistance are connected in series with the battery and galvanometer, the multimeter functions as

61. The core in a transformer provides ?

62. A mesh is any closed path in a circuit which does not enclose any other closed path inside it

63. A variable resistor in an electric circuit is for ...............

64. The separation between conduction band and valence band on the energy level diagram is called ________

65. Select the correct options only

I. Pentavalent impurities provide large number of free electrons to the semiconductor.

II. Trivalent impurities provide large number of free electrons to the semiconductor.

III. Trivalent impurities provide large number of holes to the semiconductor.

IV. Pentavalent impurities provide large number of holes to the semiconductor.

66. In electronics, _____ refers to the use of DC voltage to establish certain operating conditions for an electronic device.

67. The arrangement of atoms in a repetitive manner is known as

68. Calculate the equivalent resistance

69. A meter is protected in the case of accidental workload by connecting ............... in .............. with a voltmeter

70. An ammeter also detects the direction of the flow of current

71. Why is a laminated steel core used in a transformer instead of a solid core?

72. In checking for continuity of circuit which on these is used

73. Depletion layer serves as barrier to the movement of free electrons.

74. No electrons can stay in the forbidden gap because

75. The most versatile circuit configuration for transistors is the

76. p-type and n-type semiconductor join together to form a ................. known as ................

77. The process of setting up a current to operate a transistor at a desired point on its characteristic curve is known as __________

78. Circuit elements are connected in parallel when a common ................ is applied to each elements

79. The resistivity of a semiconductor is .......... that of an insulator, and ............that of conductors

80. A laminated steel core that has high silicon content provides

81. Calculate Rth, Vth, and I5

82. A resistor is regarded as a circuit element which puts energy into a circuit

83. A 6600/550V, 25KVA transformer has iron losses of 350W and its 1º and 2° winding resistances are 14.5 and 0.1Ω respectively. Determine the full load efficiency at a power factor of unity.

84. What are the examples of passive elements?

85. when the sensitivity of a meter is high, it means the meter has .............

86. Circuit elements connected in series have common ................. passing through each element

87. Calculate Ia, Ib and Ic

88.

How many branches, nodes, loop and mesh do we have here?

89. Which of the following is/are true

I. Reverse biasing prevents the flow of charge carriers across the junction.

II. Forward biasing is created when the positive terminal is connected to the n-type part of the PN junction.

III. In practice, when we apply reverse biasing to a PN junction, all the charge carriers stops to flow.

90. Inductors are very common in high-frequency circuit

91. Which of the following is true about transformers?

I. Open circuit test are done with a load on the transformer.

II. Copper loss is due to the ohmic resistance of the transformer windings.

III. Open circuit test is done to determine the 'no load loss' of the transformer.

IV. A transformer is electrically linked.

92. Which of this is true

93. Extrinsic semiconductors have more current conducting capacity than intrinsic semiconductors

94. A p-n junction is also known as

95. The transistor is a three-terminal device that we can use to form a _____________ circuit